| Lifetime Warranty
|
No
|
| Manufacturer Warranty
|
Guaranteed to be free from manufacturing defects
|
Model number: GL82114CF
Internet number (SKU): 301792634
Price: $9
Brand:
Availability: in stock
Similar products
Description
Eurobond 16 oz. D3 Type II Adhesive for Click and Tongue and Groove Floors in Pint Applicator Bottle - Product information
Cal-Flor's Floor Score Certified Eurobond D3/Type II Floating Floor Glue is perfect for high-strength flexibility and is far more effective against water damage than any other glue. This floating floor glue works great with pre-finished wood, laminate and engineered floating floors and is specially formulated for Click or T&G floors. Cal-Flor's Eurobond D3 Glue was the first American manufactured glue certified to meet the tough D3 European standard. For your health and the health of our environment, we've now reformulated our Eurobond Glue so it contains no formaldehyde or acrylamide (common T&G glue additives) and has a low VOC content. This improved formula has the same water-resistance, high strength and flexibility of our original D3/Type II Eurobond Glue.
- FloorScore certified, low VOC - formaldehyde and acrylamide free
- High strength, flexible cross-linking formula
- Flexibility results in a stronger bond
- Exceeds European D3/Type II standards
- Ideal for wet areas like kitchens and bathrooms
- 1 bottle covers 124 sq. ft. to 200 sq. ft.
Product reviews
Rated 5 out of
5
by
LosRubios from
This flooring glue is very easy to use, adheres well, dries quickly and is easy to clean up. We j...
This flooring glue is very easy to use, adheres well, dries quickly and is easy to clean up.
We just remodeled our laundry room and installed an 8mm thick 6" wide 'click fit' engineered wood floor however since it is a ‘wet’ room we used glue on the seams to ensure that the floor seams stay flat in the event of a water spill.
After snipping the top off to leave a 1/8” hole in the tip, it was easy to lay a consistent bead of glue on the edges of the floor boards with some light pressure. The room was quite small and I used about ¼ of the tube to glue around 120 linear feet of board edges and ends so my guess is that you could lay about 500’ linear feet of glue from a single tube.
Clean up was very easy with a damp sponge or cloth to wipe away any excess in the seams before the glue dried.
After installation, I reinstalled a whole house water filter and the washer and dryer and despite spilling a fair amount of water on the floor in the process, the seams stayed tight and flat.
Date published: 2017-09-08
Rated 5 out of
5
by
Moviedr2005 from
Easy to apply & clean up....Easy to apply & clean up.
Date published: 2018-05-30
Rated 5 out of
5
by
HGTVFAN from
This Eurobond adhesive was needed to hold some parts of the laminate floor together. Sometimes wh...This Eurobond adhesive was needed to hold some parts of the laminate floor together. Sometimes when moving on to the next row, some end in the last row had pulled apart. So we started using this adhesive fairly often.
It didn't take much to hold the pieces together. Some tape for added security until the glue dried. The applicator bottle dispensed a small amount and was easy to control. Then after tapping the boards together, just wiped the excess glue that came out of the seam.
There are sixteen ounces of glue in this bottle. Enough for up to two hundred square feet of flooring. It works well for most flooring types- wood, bamboo, cork and laminate. It is low VOC and has no formaldehyde or acrylamide. Can be used outside and is water resistant.
Date published: 2017-08-03
Rated 5 out of
5
by
bakingmom from
The Eurobond Type 11 adhesive flowed smoothly and was very easy to apply. For laminate, the tube ...The Eurobond Type 11 adhesive flowed smoothly and was very easy to apply. For laminate, the tube must be snipped to 1/16 in. at the tip and the glue flows smoothly onto the bottom surface of the groove. For wood, the tube must be snipped at 1/8 in. However, as the instructions state, you have to be careful that you don't fill the groove with glue, or it will create a gap in the flooring.The glue is easy to clean off before it dries, with soap and water or just water. One advantage is that It helps to resist moisture from the bottom which could get into the seams and damage a laminate floor, causing it to buckle. It also helps to prevent gaps from occurring in the seams, and buckling from planks being moved against each other. Normally, you have to take up a lot of flooring to replace a plank that buckles in the middle of it, so anything that adds to the durability of a floating floor is great.
Date published: 2017-12-12
Rated 4 out of
5
by
JamesC from
Eurobond 16 oz. D3 Type II Adhesive for Click and Tongue and Groove Floors in Pint Applicator Bottle is a must for use with laminate or engineered hardwood floating floors that rely on a tongue and groove or click lock joinery. I have correctly installed a number of floating laminate floors, and no matter how well installed, they eventually all, from constant walking on them in different directions, suffer from plank separation at the joints if not glued. I also use this glue for joining hardwood flooring installed close to a wall or in tight spaces where use of a flooring nailer is not possible. The applicator tip can be snipped off to the desired flow. Snipping the very end allows for glue to be applied with precision. The more of the tip that is cut off, the heavier the flow will be, resulting in less precise application. The glue is thin and flows easily from the applicator tip, without clogging, so its not necessary to cut back the applicator tip too far. A thin bead of glue is all that t takes to permanently join the flooring. Other glues are messy and run all over the place, either because those glues are too thin or the applicator tip allows too much flow. The odor of the D3 Type II Adhesive is low, the glue sets up fairly quickly, and cleans up with water. Replacing the cap when not in use helps prevent the glue from drying in the bottle. If you have excess glue, you can use if for other wood projects. This glue performs well and I am very satisfied with it.
Date published: 2017-11-27
Rated 5 out of
5
by
Jayhawk714 from
So far I am really impressed with the Eurobond 16 oz. D3 Type II Adhesive for Click and Tongue an...So far I am really impressed with the Eurobond 16 oz. D3 Type II Adhesive for Click and Tongue and Groove Floors in Pint Applicator Bottle. It's advertiser for floating floors, however, I have been testing it on 3/4 inch Tongue and Grove Pine and so far it is holding up very good. I do a lot of woodworking and have been making a lot of Blue Pine chests of all size's. I am going to run the pine through my router as Tongue and Grove and use this adhesive to build it. The way my test pieces are turning out I don't foresee and problems as far as strength goes. The big test will be the holding strength when I glue up and clamp some of the bowed pine. But again, I feel this adhesive will do just fine. You can cut the nozzle as small or large as you need it and it comes out very easily. One bottle can do up to 200 square feet so one bottle will be enough to do a good sized chest or more.
Date published: 2017-10-28
Rated 5 out of
5
by
Nick from
best product ever. ...best product ever.
Date published: 2018-02-10
Rated 5 out of
5
by
FXP1 from
Eurobond 16 oz. D3 Type II Adhesive for Click and Tongue and Groove Floors in Pint Applicator Bot...Eurobond 16 oz. D3 Type II Adhesive for Click and Tongue and Groove Floors in Pint Applicator Bottle is a white glue formulated for flooring. PVC glue can be used on a variety of surfaces. It works on wood, MDF, chipboard as an adhesive, sealer,. The applicator bottle is easy to use and puts out a thin bead which you set by snipping the tip open. I tried it on an area where the tongue and groove joints were opening around a closet in the floating floor. These joints are supposed to hold, but that's not always the case no matter how many times I tapped them back in with a maillot and the special block tool. Glue has the consistency, in my opinion, of Elmer's and flowed easily through the 1 1/16-inch hole I made. Was careful not to overfill the groove and pushed the planks back together and gave them a tap with the maillot and block. I then wiped any excess glue that came up and was finished. The instructions said to wait a day before walking on the floor. We'll see how well it holds, but its cheap insurance than trusting those tongue and grooves to hold on their own. I wish I knew about this glue when I was first putting down the floor. I would have used it as a precaution to what is now happening.
Date published: 2017-08-27
